bigip_profile_oneconnect – Manage OneConnect profiles on a BIG-IP

New in version 2.7.

Synopsis

Manage OneConnect profiles on a BIG-IP.

Parameters

Parameter		Choices/Defaults	Comments
description string			Description of the profile.
idle_timeout_override string			Specifies the number of seconds that a connection is idle before the connection flow is eligible for deletion. When creating a new profile, if this parameter is not specified, the default is provided by the parent profile. You may specify a number of seconds for the timeout override. When `disabled`, specifies that there is no timeout override for the connection. When `indefinite`, Specifies that a connection may be idle with no timeout override.
limit_type string		Choices: none idle strict	When `none`, simultaneous in-flight requests and responses over TCP connections to a pool member are counted toward the limit. This is the historical behavior. When `idle`, idle connections will be dropped as the TCP connection limit is reached. For short intervals, during the overlap of the idle connection being dropped and the new connection being established, the TCP connection limit may be exceeded. When `strict`, the TCP connection limit is honored with no exceptions. This means that idle connections will prevent new TCP connections from being made until they expire, even if they could otherwise be reused. `strict` is not a recommended configuration except in very special cases with short expiration timeouts. When creating a new profile, if this parameter is not specified, the default is provided by the parent profile.
maximum_age integer			Specifies the maximum number of seconds allowed for a connection in the connection reuse pool. For any connection with an age higher than this value, the system removes that connection from the re-use pool. When creating a new profile, if this parameter is not specified, the default is provided by the parent profile.
maximum_reuse integer			Specifies the maximum number of times that a server-side connection can be reused. When creating a new profile, if this parameter is not specified, the default is provided by the parent profile.
maximum_size integer			Specifies the maximum number of connections that the system holds in the connection reuse pool. If the pool is already full, then a server-side connection closes after the response is completed. When creating a new profile, if this parameter is not specified, the default is provided by the parent profile.
name string / required			Specifies the name of the OneConnect profile.
parent string			Specifies the profile from which this profile inherits settings. When creating a new profile, if this parameter is not specified, the default is the system-supplied `oneconnect` profile.
partition string		Default: "Common"	Device partition to manage resources on.
password string / required			The password for the user account used to connect to the BIG-IP. You may omit this option by setting the environment variable `F5_PASSWORD`. aliases: pass, pwd
provider dictionary added in 2.5			A dict object containing connection details.
	password string / required		The password for the user account used to connect to the BIG-IP. You may omit this option by setting the environment variable `F5_PASSWORD`. aliases: pass, pwd
	server string / required		The BIG-IP host. You may omit this option by setting the environment variable `F5_SERVER`.
	server_port integer	Default: 443	The BIG-IP server port. You may omit this option by setting the environment variable `F5_SERVER_PORT`.
	ssh_keyfile path		Specifies the SSH keyfile to use to authenticate the connection to the remote device. This argument is only used for cli transports. You may omit this option by setting the environment variable `ANSIBLE_NET_SSH_KEYFILE`.
	timeout integer	Default: 10	Specifies the timeout in seconds for communicating with the network device for either connecting or sending commands. If the timeout is exceeded before the operation is completed, the module will error.
	transport string	Choices: cli rest ←	Configures the transport connection to use when connecting to the remote device.
	user string / required		The username to connect to the BIG-IP with. This user must have administrative privileges on the device. You may omit this option by setting the environment variable `F5_USER`.
	validate_certs boolean	Choices: no yes ←	If `no`, SSL certificates are not validated. Use this only on personally controlled sites using self-signed certificates. You may omit this option by setting the environment variable `F5_VALIDATE_CERTS`.
server string / required			The BIG-IP host. You may omit this option by setting the environment variable `F5_SERVER`.
server_port integer added in 2.2		Default: 443	The BIG-IP server port. You may omit this option by setting the environment variable `F5_SERVER_PORT`.
share_pools boolean		Choices: no yes	Indicates that connections may be shared not only within a virtual server, but also among similar virtual servers When `yes`, all virtual servers that use the same OneConnect and other internal network profiles can share connections. When creating a new profile, if this parameter is not specified, the default is provided by the parent profile.
source_mask string			Specifies a value that the system applies to the source address to determine its eligibility for reuse. When creating a new profile, if this parameter is not specified, the default is provided by the parent profile. The system applies the value of this setting to the server-side source address to determine its eligibility for reuse. A mask of `0` causes the system to share reused connections across all source addresses. A host mask of `32` causes the system to share only those reused connections originating from the same source address. When you are using a SNAT or SNAT pool, the server-side source address is translated first and then the OneConnect mask is applied to the translated address.
state string		Choices: present ← absent	When `present`, ensures that the profile exists. When `absent`, ensures the profile is removed.
user string / required			The username to connect to the BIG-IP with. This user must have administrative privileges on the device. You may omit this option by setting the environment variable `F5_USER`.
validate_certs boolean added in 2.0		Choices: no yes ←	If `no`, SSL certificates are not validated. Use this only on personally controlled sites using self-signed certificates. You may omit this option by setting the environment variable `F5_VALIDATE_CERTS`.

Notes

Note

For more information on using Ansible to manage F5 Networks devices see https://www.ansible.com/integrations/networks/f5.
Requires BIG-IP software version >= 12.
The F5 modules only manipulate the running configuration of the F5 product. To ensure that BIG-IP specific configuration persists to disk, be sure to include at least one task that uses the bigip_config module to save the running configuration. Refer to the module’s documentation for the correct usage of the module to save your running configuration.

Examples

- name: Create a OneConnect profile
  bigip_profile_oneconnect:
    name: foo
    state: present
    provider:
      user: admin
      password: secret
      server: lb.mydomain.com
  delegate_to: localhost

Return Values

Common return values are documented here, the following are the fields unique to this module:

Key	Returned	Description
description string	changed	Description of the profile. Sample: My profile
idle_timeout_override string	changed	The new idle timeout override. Sample: disabled
limit_type string	changed	New limit type of the profile. Sample: idle
maximum_age integer	changed	Maximum number of seconds allowed for a connection in the connection reuse pool. Sample: 2000
maximum_reuse integer	changed	Maximum number of times that a server-side connection can be reused. Sample: 1000
maximum_size integer	changed	Maximum number of connections that the system holds in the connection reuse pool. Sample: 3000
share_pools boolean	changed	Share connections among similar virtual servers. Sample: True
source_mask string	changed	Value that the system applies to the source address to determine its eligibility for reuse. Sample: 255.255.255.255

Status

This module is not guaranteed to have a backwards compatible interface. [preview]
This module is maintained by an Ansible Partner. [certified]

Authors

Tim Rupp (@caphrim007)

Hint

If you notice any issues in this documentation you can edit this document to improve it.

© 2012–2018 Michael DeHaan
© 2018–2019 Red Hat, Inc.
Licensed under the GNU General Public License version 3.
https://docs.ansible.com/ansible/2.8/modules/bigip_profile_oneconnect_module.html

Docs

Docs4dev

Title here