cisco.iosxr.iosxr_ospf_interfaces – OSPF Interfaces Resource Module.

Note

This plugin is part of the cisco.iosxr collection (version 2.5.0).

You might already have this collection installed if you are using the ansible package. It is not included in ansible-core. To check whether it is installed, run ansible-galaxy collection list.

To install it, use: ansible-galaxy collection install cisco.iosxr.

To use it in a playbook, specify: cisco.iosxr.iosxr_ospf_interfaces.

New in version 1.2.0: of cisco.iosxr

Synopsis

This module manages OSPF(v2/v3) configuration of interfaces on devices running Cisco IOS-XR.

Note

This module has a corresponding action plugin.

Parameters

Parameter							Choices/Defaults	Comments
config list / elements=dictionary								A list of OSPF configuration for interfaces.
	address_family list / elements=dictionary							OSPF settings on the interfaces in address-family context.
		afi string / required					Choices: ipv4 ipv6	Address Family Identifier (AFI) for OSPF settings on the interfaces.
		apply_group_option dictionary						Specify configuration from a group
			group_name string					Specify the name of the group
			operation string				Choices: add remove append	Specify the group config operation
		authentication dictionary						Enable authentication
			message_digest dictionary					Use message-digest authentication
				keychain string				Specify keychain name
			null_auth boolean				Choices: no yes	Use no authentication
		authentication_key dictionary						Specify authentication password (key)
			clear string					Specifies an UNENCRYPTED password (key) will follow
			encrypted string					Specifies an ENCRYPTED password (key) will follow
			password string					The OSPFv2 password (key)
		bfd dictionary						Configure BFD parameters
			fast_detect dictionary					Configure fast detection
				set boolean			Choices: no yes	Enable fast detection only
				strict_mode boolean			Choices: no yes	Hold down neighbor session until BFD session is up
			minimum_interval integer					Hello interval in milli-seconds
			multiplier integer					Detect multiplier
		cost integer						Specify Interface cost
		cost_fallback dictionary						Specify Cost when cumulative bandwidth goes below the theshold
			cost integer					Specify cost w.r.t cummulative bandwidth
			threshold integer					Specify threshold bandwidth when cost-fallback is applied
		database_filter dictionary						Filter OSPF LSAs during synchronization and flooding
			all_outgoing_lsa boolean				Choices: no yes	Filter all outgoing LSA
		dead_interval integer						Specify interval after which a neighbor is declared dead
		demand_circuit boolean					Choices: no yes	Enable/Disable demand circuits
		fast_reroute dictionary						Specify IP Fast Reroute
			disabled boolean				Choices: no yes	Disable IP fast reroute
			per_link dictionary					Specify per-prefix computation
				information_type string			Choices: exclude lfa_candidate	Specify per-link LFA exclusion or FRR LFA candidate information
				interface dictionary				Specify Per-link LFA exclusion information
					bundle_ether list / elements=dictionary			Specify Aggregated Ethernet interface(s)
						name integer		Specify the interface id
					bvi list / elements=dictionary			Specify Bridge-Group Virtual Interface
						name integer		Specify the interface id
					fast_ethernet list / elements=dictionary			Specify FastEthernet/IEEE 802.3 interface(s)
						name string		Specify the interface id
					fiftygige list / elements=dictionary			Specify FiftyGigE/IEEE 802.3 interface(s)
						name string		Specify the interface id
					fortygige list / elements=dictionary			Specify FortyGigE/IEEE 802.3 interface(s)
						name string		Specify the interface id
					fourhundredgige list / elements=dictionary			Specify FourHundredGigE/IEEE 802.3 interface(s)
						name string		Specify the interface id
					gigabitethernet list / elements=dictionary			Specify GigabitEthernet/IEEE 802.3 interface(s)
						name string		Specify the interface id
					hundredgige list / elements=dictionary			Specify HundredGigE/IEEE 802.3 interface(s)
						name string		Specify the interface id
					mgmteth list / elements=dictionary			Specify MgmtEth/IEEE 802.3 interface(s)
						name string		Specify the interface id
					multilink list / elements=dictionary			Specify Multilink network interface(s)
						name string		Specify the interface id
					nve list / elements=dictionary			Specify Network Virtualization Endpoint Interface(s)
						name integer		Specify the interface id
					pos_int list / elements=dictionary			Specify Aggregated pos interface(s)
						name integer		Specify the interface id
					pw_ether list / elements=dictionary			Specify PWHE Ethernet Interface
						name integer		Specify the interface id
					pw_iw list / elements=dictionary			Specify PWHE VC11 IP Interworking Interface
						name integer		Specify the interface id
					serial list / elements=dictionary			Specify Serial network interface(s)
						name string		Specify the interface id
					srp list / elements=dictionary			Specify SRP interface(s)
						name string		Specify the interface id
					tengige list / elements=dictionary			Specify TenGigabitEthernet/IEEE 802.3 interface(s)
						name string		Specify the interface id
					tunnel_ip list / elements=dictionary			Specify GRE/IPinIP Tunnel Interface(s)
						name integer		Specify the interface id
					tunnel_ipsec list / elements=dictionary			Specify IPSec Tunnel interface(s)
						name integer		Specify the interface id
					tunnel_mpls list / elements=dictionary			MPLS Transport Protocol Tunnel interface
						name string		Specify the interface id
					tunnel_mte list / elements=dictionary			Specify MPLS Traffic Engineering P2MP Tunnel interface(s)
						name integer		Specify the interface id
					twentyfivegige list / elements=dictionary			Specify TwentyFiveGigabitEthernet/IEEE 802.3 interface(s)
						name string		Specify the interface id
					twohundredgige list / elements=dictionary			Specify TwoHundredGigE/IEEE 802.3 interface(s)
						name string		Specify the interface id
				use_candidate_only boolean			Choices: no yes	Enable/Disable backup selection from candidate-list only
		flood_reduction boolean					Choices: no yes	Enable/Disable flood reduction
		hello_interval integer						Specify Time between HELLO packets
		link_down_fast_detect boolean					Choices: no yes	Configure interface down parameters
		message_digest_key dictionary						Message digest authentication password (key)
			id integer / required					Key ID
			md5 dictionary / required					Use MD5 Algorithm
				clear boolean			Choices: no yes	Specifies an UNENCRYPTED password (key) will follow
				encrypted boolean			Choices: no yes	Specifies an ENCRYPTED password (key) will follow
				password string				The OSPFv2 password (key)
		mpls_ldp_sync boolean					Choices: no yes	Enable/Disable MPLS LDP Sync
		mtu_ignore boolean					Choices: no yes	Enable/Disable ignoring of MTU in DBD packets
		neighbors list / elements=dictionary						Specify a neighbor routers
			cost integer					Specify OSPF cost for point-to-multipoint neighbor
			db_filter_all_out boolean				Choices: no yes	Specify Filter OSPF LSA during synchronization and flooding for point-to-multipoint neighbor
			neighbor_id string					Specify Neighbor address (name)
			poll_interval integer					Specify OSPF dead-router polling interval
			priority integer					Specify OSPF priority of non-broadcast neighbor
		network string					Choices: broadcast non-broadcast point-to-multipoint point-to-point	Specify Network type
		packet_size integer						Customize size of OSPF packets upto MTU
		passive boolean					Choices: no yes	Enable/Disable passive
		prefix_suppression boolean					Choices: no yes	Suppress advertisement of the prefixes
		priority integer						Specify Router priority
		processes list / elements=dictionary						Interfaces configuration for an OSPF process.
			area dictionary					Specify the area-id
				area_id string				OSPF interfaces area ID as a decimal value. Please refer vendor documentation of Valid values. OSPF interfaces area ID in IP address format(e.g. A.B.C.D)
			process_id string / required					OSPF process tag.
		retransmit_interval integer						Specify time between retransmitting lost link state advertisements
		security_ttl dictionary						Enable security
			hops integer					Maximum number of IP hops allowed <1-254>
			set boolean				Choices: no yes	Enable ttl security
		transmit_delay integer						Specify estimated time needed to send link-state update packet
	name string / required							Name/Identifier of the interface.
	type string / required							Type of the interface.
running_config string								This option is used only with state parsed. The value of this option should be the output received from the IOS-XR device by executing the command show running-config router ospf'. The state parsed reads the configuration from `running_config` option and transforms it into Ansible structured data as per the resource module's argspec and the value is then returned in the parsed key within the result.
state string							Choices: merged ← replaced overridden deleted gathered parsed rendered	The state the configuration should be left in.

Notes

Note

This module works with connection network_cli. See the IOS-XR Platform Options

Examples

# Using merged

# Before state:
# -------------
#
# RP/0/RP0/CPU0:anton#show running-config router ospf
# % No such configuration item(s)
#

- name: Merge provided OSPF interfaces configuration with the existing configuration
  cisco.iosxr.iosxr_ospf_interfaces:
    config:
      - name: GigabitEthernet0/0/0/0
        type: gigabitethernet
        address_family:
          - afi: ipv4
            processes:
              - process_id: "LAB3"
                area:
                  area_id: 0.0.0.3
            cost: 20
            authentication:
              message_digest:
                keychain: cisco
          - afi: ipv6
            processes:
              - process_id: "LAB3"
                area:
                  area_id: 0.0.0.2
            cost: 30
    state: merged

#
#
# ------------------------
# Module Execution Result
# ------------------------
#
#  "before": []
#
#  "commands": [
#        "router ospf LAB3 area 0.0.0.3 interface GigabitEthernet 0/0/0/0 cost 20",
#        "router ospf LAB3 area 0.0.0.3 interface GigabitEthernet 0/0/0/0 authentication message-digest",
#        "router ospf LAB3 area 0.0.0.3 interface GigabitEthernet 0/0/0/0 authentication message-digest keychain cisco",
#        "router ospfv3 LAB3 area 0.0.0.2 interface GigabitEthernet 0/0/0/0 cost 30"
#     ]
#
#  "after": [
#         {
#             "address_family": [
#                 {
#                     "afi": "ipv4",
#                     "authentication": {
#                         "message_digest": {
#                             "keychain": "cisco"
#                         }
#                     },
#                     "cost": 20,
#                     "processes": [
#                         {
#                             "area": {
#                                 "area_id": "0.0.0.3"
#                             },
#                             "process_id": "LAB3"
#                         }
#                     ]
#                 },
#                 {
#                     "afi": "ipv6",
#                     "cost": 30,
#                     "processes": [
#                         {
#                             "area": {
#                                 "area_id": "0.0.0.2"
#                             },
#                             "process_id": "LAB3"
#                         }
#                     ]
#                 }
#             ],
#             "name": "GigabitEthernet0/0/0/0",
#             "type": "gigabitethernet"
#         }
#     ]
#
#
# ------------
# After state
# ------------
#
# RP/0/0/CPU0:an-iosxr-02#show running-config router ospf
# Thu Oct 23 06:00:57.217 UTC
# router ospf LAB
#  area 0.0.0.0
#  !
#  area 0.0.0.9
#  !
# !
# router ospf LAB1
#  area 0.0.0.1
#  !
#  area 0.0.0.3
#  !
# !
# router ospf LAB3
#  area 0.0.0.3
#   interface GigabitEthernet0/0/0/0
#    cost 20
#    authentication message-digest keychain cisco
#   !
#  !
# !
# router ospf ipv4
# !

# Using replaced
#
# ------------
# Before state
# ------------
#
#
# RP/0/0/CPU0:an-iosxr-02#show running-config router ospf
# Thu Oct 23 06:00:57.217 UTC
# router ospf LAB
#  area 0.0.0.0
#  !
#  area 0.0.0.9
#  !
# !
# router ospf LAB1
#  area 0.0.0.1
#  !
#  area 0.0.0.3
#  !
# !
# router ospf LAB3
#  area 0.0.0.3
#   interface GigabitEthernet0/0/0/0
#    cost 20
#    authentication message-digest keychain cisco
#   !
#  !
# !
# router ospf ipv4
# !

- name: Replace OSPF interfaces configuration
  cisco.iosxr.iosxr_ospf_interfaces:
    config:
      - name: GigabitEthernet0/0/0/0
        type: gigabitethernet
        address_family:
          - afi: ipv4
            processes:
              - process_id: "LAB3"
                area:
                  area_id: 0.0.0.3
            cost: 30
            authentication:
              message_digest:
                keychain: ciscoiosxr
          - afi: ipv6
            processes:
              - process_id: "LAB3"
                area:
                  area_id: 0.0.0.2
            cost: 30
    state: replaced

#
#
# ------------------------
# Module Execution Result
# ------------------------
#
#  "before": [
#         {
#             "address_family": [
#                 {
#                     "afi": "ipv4",
#                     "authentication": {
#                         "message_digest": {
#                             "keychain": "cisco"
#                         }
#                     },
#                     "cost": 20,
#                     "processes": [
#                         {
#                             "area": {
#                                 "area_id": "0.0.0.3"
#                             },
#                             "process_id": "LAB3"
#                         }
#                     ]
#                 },
#                 {
#                     "afi": "ipv6",
#                     "cost": 30,
#                     "processes": [
#                         {
#                             "area": {
#                                 "area_id": "0.0.0.2"
#                             },
#                             "process_id": "LAB3"
#                         }
#                     ]
#                 }
#             ],
#             "name": "GigabitEthernet0/0/0/0",
#             "type": "gigabitethernet"
#         }
#     ]
#
#  "commands": [
#    "router ospf LAB3 area 0.0.0.3 interface GigabitEthernet 0/0/0/0 cost 30",
#    "router ospf LAB3 area 0.0.0.3 interface GigabitEthernet 0/0/0/0 authentication message-digest",
#    "router ospf LAB3 area 0.0.0.3 interface GigabitEthernet 0/0/0/0 authentication message-digest keychain ciscoiosxr"
#     ]
#
#  "after": [
#         {
#             "address_family": [
#                 {
#                     "afi": "ipv4",
#                     "authentication": {
#                         "message_digest": {
#                             "keychain": "ciscoiosxr"
#                         }
#                     },
#                     "cost": 30,
#                     "processes": [
#                         {
#                             "area": {
#                                 "area_id": "0.0.0.3"
#                             },
#                             "process_id": "LAB3"
#                         }
#                     ]
#                 },
#                 {
#                     "afi": "ipv6",
#                     "cost": 30,
#                     "processes": [
#                         {
#                             "area": {
#                                 "area_id": "0.0.0.2"
#                             },
#                             "process_id": "LAB3"
#                         }
#                     ]
#                 }
#             ],
#             "name": "GigabitEthernet0/0/0/0",
#             "type": "gigabitethernet"
#         }
#     ]
#
#
# -----------
# After state
# -----------
#
# RP/0/0/CPU0:an-iosxr-02#show running-config router ospf
# Thu Oct 23 06:10:39.827 UTC
# router ospf LAB
#  area 0.0.0.0
#  !
#  area 0.0.0.9
#  !
# !
# router ospf LAB1
#  area 0.0.0.1
#  !
#  area 0.0.0.3
#  !
# !
# router ospf LAB3
#  area 0.0.0.3
#   interface GigabitEthernet0/0/0/0
#    cost 30
#    authentication message-digest keychain ciscoiosxr
#   !
#  !
# !
# router ospf ipv4
# !

- name: Override existing OSPF interfaces configuration
  cisco.iosxr.iosxr_ospf_interfaces:
    config:
      - name: GigabitEthernet0/0/0/1
        type: gigabitethernet
        address_family:
          - afi: ipv4
            processes:
              - process_id: "LAB1"
                area:
                  area_id: 0.0.0.3
            cost: 10
            authentication:
              message_digest:
                keychain: iosxr
    state: overridden

#
#
# ------------------------
# Module Execution Result
# ------------------------
#
#  "before": [
#         {
#             "address_family": [
#                 {
#                     "afi": "ipv4",
#                     "authentication": {
#                         "message_digest": {
#                             "keychain": "ciscoiosxr"
#                         }
#                     },
#                     "cost": 30,
#                     "processes": [
#                         {
#                             "area": {
#                                 "area_id": "0.0.0.3"
#                             },
#                             "process_id": "LAB3"
#                         }
#                     ]
#                 },
#                 {
#                     "afi": "ipv6",
#                     "cost": 30,
#                     "processes": [
#                         {
#                             "area": {
#                                 "area_id": "0.0.0.2"
#                             },
#                             "process_id": "LAB3"
#                         }
#                     ]
#                 }
#             ],
#             "name": "GigabitEthernet0/0/0/0",
#             "type": "gigabitethernet"
#         }
#     ]
#
#  "commands": [
#         "no router ospf LAB3 area 0.0.0.3 interface GigabitEthernet 0/0/0/0",
#         "no router ospfv3 LAB3 area 0.0.0.2 interface GigabitEthernet 0/0/0/0",
#         "router ospf LAB1 area 0.0.0.3 interface GigabitEthernet 0/0/0/1 cost 10",
#         "router ospf LAB1 area 0.0.0.3 interface GigabitEthernet 0/0/0/1 authentication message-digest",
#         "router ospf LAB1 area 0.0.0.3 interface GigabitEthernet 0/0/0/1 authentication message-digest keychain iosxr"
#     ]
#
#  "after": [
#         {
#             "address_family": [
#                 {
#                     "afi": "ipv4",
#                     "authentication": {
#                         "message_digest": {
#                             "keychain": "iosxr"
#                         }
#                     },
#                     "cost": 10,
#                     "processes": [
#                         {
#                             "area": {
#                                 "area_id": "0.0.0.3"
#                             },
#                             "process_id": "LAB1"
#                         }
#                     ]
#                 }
#             ],
#             "name": "GigabitEthernet0/0/0/1",
#             "type": "gigabitethernet"
#         }
#     ]
#
#
# -----------
# After state
# -----------
#
# RP/0/0/CPU0:an-iosxr-02#show running-config router ospf
# Thu Oct 23 06:28:15.025 UTC
# router ospf LAB
#  area 0.0.0.0
#  !
#  area 0.0.0.9
#  !
# !
# router ospf LAB1
#  area 0.0.0.1
#  !
#  area 0.0.0.3
#   interface GigabitEthernet0/0/0/1
#    cost 10
#    authentication message-digest keychain iosxr
#   !
#  !
# !
# router ospf LAB3
#  area 0.0.0.3
#  !
# !
# router ospf ipv4
# !

# Using deleted
#
# ------------
# Before state
# ------------
#
#
# RP/0/0/CPU0:an-iosxr-02#show running-config router ospf
# Thu Oct 23 06:28:15.025 UTC
# router ospf LAB
#  area 0.0.0.0
#  !
#  area 0.0.0.9
#  !
# !
# router ospf LAB1
#  area 0.0.0.1
#  !
#  area 0.0.0.3
#   interface GigabitEthernet0/0/0/1
#    cost 10
#    authentication message-digest keychain iosxr
#   !
#  !
# !
# router ospf LAB3
#  area 0.0.0.3
#  !
# !
# router ospf ipv4
# !

- name: Deleted existing OSPF interfaces from the device
  cisco.iosxr.iosxr_ospf_interfaces:
    config:
      - name: GigabitEthernet0/0/0/1
        type: gigabitethernet
    state: deleted

#
#
# ------------------------
# Module Execution Result
# ------------------------
#
#  "before": [
#         {
#             "address_family": [
#                 {
#                     "afi": "ipv4",
#                     "authentication": {
#                         "message_digest": {
#                             "keychain": "iosxr"
#                         }
#                     },
#                     "cost": 10,
#                     "processes": [
#                         {
#                             "area": {
#                                 "area_id": "0.0.0.3"
#                             },
#                             "process_id": "LAB1"
#                         }
#                     ]
#                 }
#             ],
#             "name": "GigabitEthernet0/0/0/1",
#             "type": "gigabitethernet"
#         }
#     ],
#
#  "commands": [
#         "no router ospf LAB1 area 0.0.0.3 interface GigabitEthernet 0/0/0/1"
#     ]
#
#  "after": []
#
#
# -----------
# After state
# -----------
#
# RP/0/0/CPU0:an-iosxr-02#show running-config router ospf
# Thu Oct 23 06:34:38.319 UTC
# router ospf LAB
#  area 0.0.0.0
#  !
#  area 0.0.0.9
#  !
# !
# router ospf LAB1
#  area 0.0.0.1
#  !
#  area 0.0.0.3
#  !
# !
# router ospf LAB3
#  area 0.0.0.3
#  !
# !
# router ospf ipv4
# !

# Using parsed
# parsed.cfg
# ------------
# router ospf LAB
#  area 0.0.0.0
#  !
#  area 0.0.0.9
#  !
# !
# router ospf LAB1
#  area 0.0.0.1
#  !
#  area 0.0.0.3
#  !
# !
# router ospf LAB3
#  area 0.0.0.3
#   interface GigabitEthernet0/0/0/0
#    cost 20
#    authentication message-digest keychain cisco
#   !
#  !
# !
# router ospf ipv4
# !
- name: Parsed the device configuration to get output commands
  cisco.iosxr.iosxr_ospf_interfaces:
    running_config: "{{ lookup('file', './parsed.cfg') }}"
    state: parsed
#
#
# -------------------------
# Module Execution Result
# -------------------------
#
#
# "parsed": [
#         {
#             "address_family": [
#                 {
#                     "afi": "ipv4",
#                     "authentication": {
#                         "message_digest": {
#                             "keychain": "cisco"
#                         }
#                     },
#                     "cost": 20,
#                     "processes": [
#                         {
#                             "area": {
#                                 "area_id": "0.0.0.3"
#                             },
#                             "process_id": "LAB3"
#                         }
#                     ]
#                 }
#             ],
#             "name": "GigabitEthernet0/0/0/0",
#             "type": "gigabitethernet"
#         }
#     ]
#
# Using rendered
#
#
- name: Render the commands for provided  configuration
  cisco.iosxr.iosxr_ospf_interfaces:
    config:
      - name: GigabitEthernet0/0/0/0
        type: gigabitethernet
        address_family:
          - afi: ipv4
            processes:
             - process_id: "LAB3"
               area:
                 area_id: 0.0.0.3
            cost: 20
            authentication:
              message_digest:
                keychain: cisco
          - afi: ipv6
            processes:
             - process_id: "LAB3"
               area:
                 area_id: 0.0.0.2
            cost: 30
    state: rendered

#
#
# -------------------------
# Module Execution Result
# -------------------------
#
#
# "rendered": [
#        "router ospf LAB3 area 0.0.0.3 interface GigabitEthernet 0/0/0/0 cost 20",
#        "router ospf LAB3 area 0.0.0.3 interface GigabitEthernet 0/0/0/0 authentication message-digest",
#        "router ospf LAB3 area 0.0.0.3 interface GigabitEthernet 0/0/0/0 authentication message-digest keychain cisco",
#        "router ospfv3 LAB3 area 0.0.0.2 interface GigabitEthernet 0/0/0/0 cost 30"
#     ]


# Using gathered
#
# Before state:
# -------------
#
# RP/0/0/CPU0:an-iosxr-02#show running-config router ospf
# Thu Oct 23 06:50:38.743 UTC
# router ospf LAB
#  area 0.0.0.0
#  !
#  area 0.0.0.9
#  !
# !
# router ospf LAB1
#  area 0.0.0.1
#  !
#  area 0.0.0.3
#  !
# !
# router ospf LAB3
#  area 0.0.0.3
#   interface GigabitEthernet0/0/0/0
#    cost 20
#    authentication message-digest keychain cisco
#   !
#  !
# !
# router ospf ipv4
# !


- name: Gather ospf_interfaces routes configuration
  cisco.iosxr.iosxr_ospf_interfaces:
    state: gathered
#
#
# -------------------------
# Module Execution Result
# -------------------------
#
#    "gathered": [
#         {
#             "address_family": [
#                 {
#                     "afi": "ipv4",
#                     "authentication": {
#                         "message_digest": {
#                             "keychain": "cisco"
#                         }
#                     },
#                     "cost": 20,
#                     "processes": [
#                         {
#                             "area": {
#                                 "area_id": "0.0.0.3"
#                             },
#                             "process_id": "LAB3"
#                         }
#                     ]
#                 },
#                 {
#                     "afi": "ipv6",
#                     "cost": 30,
#                     "processes": [
#                         {
#                             "area": {
#                                 "area_id": "0.0.0.2"
#                             },
#                             "process_id": "LAB3"
#                         }
#                     ]
#                 }
#             ],
#             "name": "GigabitEthernet0/0/0/0",
#             "type": "gigabitethernet"
#         }
#     ]
#

Authors

Rohit Thakur (@rohitthakur2590)

© 2012–2018 Michael DeHaan
© 2018–2021 Red Hat, Inc.
Licensed under the GNU General Public License version 3.
https://docs.ansible.com/ansible/latest/collections/cisco/iosxr/iosxr_ospf_interfaces_module.html

Docs

Docs4dev

Title here

cisco.iosxr.iosxr_ospf_interfaces – OSPF Interfaces Resource Module.

Synopsis

Parameters

Notes

Examples

Authors