community.network.ce_sflow – Manages sFlow configuration on HUAWEI CloudEngine switches.

Note

This plugin is part of the community.network collection (version 3.0.0).

You might already have this collection installed if you are using the ansible package. It is not included in ansible-core. To check whether it is installed, run ansible-galaxy collection list.

To install it, use: ansible-galaxy collection install community.network.

To use it in a playbook, specify: community.network.ce_sflow.

Synopsis

Configure Sampled Flow (sFlow) to monitor traffic on an interface in real time, detect abnormal traffic, and locate the source of attack traffic, ensuring stable running of the network.

Parameters

Parameter	Choices/Defaults	Comments
agent_ip string		Specifies the IPv4/IPv6 address of an sFlow agent.
collector_datagram_size string		Specifies the maximum length of sFlow packets sent from an sFlow agent to an sFlow collector. The value is an integer, in bytes. It ranges from 1024 to 8100. The default value is 1400.
collector_description string		Specifies the description of an sFlow collector. The value is a string of 1 to 255 case-sensitive characters without spaces.
collector_id string	Choices: 1 2	Specifies the ID of an sFlow collector. This ID is used when you specify the collector in subsequent sFlow configuration.
collector_ip string		Specifies the IPv4/IPv6 address of the sFlow collector.
collector_ip_vpn string		Specifies the name of a VPN instance. The value is a string of 1 to 31 case-sensitive characters, spaces not supported. When double quotation marks are used around the string, spaces are allowed in the string. The value `_public_` is reserved and cannot be used as the VPN instance name.
collector_meth string	Choices: meth enhanced	Configures the device to send sFlow packets through service interfaces, enhancing the sFlow packet forwarding capability. The enhanced parameter is optional. No matter whether you configure the enhanced mode, the switch determines to send sFlow packets through service cards or management port based on the routing information on the collector. When the value is meth, the device forwards sFlow packets at the control plane. When the value is enhanced, the device forwards sFlow packets at the forwarding plane to enhance the sFlow packet forwarding capacity.
collector_udp_port string		Specifies the UDP destination port number of sFlow packets. The value is an integer that ranges from 1 to 65535. The default value is 6343.
counter_collector string		Indicates the ID list of the counter collector.
counter_interval string		Indicates the counter sampling interval. The value is an integer that ranges from 10 to 4294967295, in seconds. The default value is 20.
export_route string	Choices: enable disable	Configures the sFlow packets sent by the switch not to carry routing information.
sample_collector string		Indicates the ID list of the collector.
sample_direction string	Choices: inbound outbound both	Enables flow sampling in the inbound or outbound direction.
sample_length string		Specifies the maximum length of sampled packets. The value is an integer and ranges from 18 to 512, in bytes. The default value is 128.
sample_rate string		Specifies the flow sampling rate in the format 1/rate. The value is an integer and ranges from 1 to 4294967295. The default value is 8192.
sflow_interface string		Full name of interface for Flow Sampling or Counter. It must be a physical interface, Eth-Trunk, or Layer 2 subinterface.
source_ip string		Specifies the source IPv4/IPv6 address of sFlow packets.
state string	Choices: present ← absent	Determines whether the config should be present or not on the device.

Notes

Note

This module requires the netconf system service be enabled on the remote device being managed.
Recommended connection is netconf.
This module also works with local connections for legacy playbooks.

Examples

---

- name: Sflow module test
  hosts: ce128
  connection: local
  gather_facts: no
  vars:
    cli:
      host: "{{ inventory_hostname }}"
      port: "{{ ansible_ssh_port }}"
      username: "{{ username }}"
      password: "{{ password }}"
      transport: cli

  tasks:
  - name: Configuring sFlow Agent
    community.network.ce_sflow:
      agent_ip: 6.6.6.6
      provider: '{{ cli }}'

  - name: Configuring sFlow Collector
    community.network.ce_sflow:
      collector_id: 1
      collector_ip: 7.7.7.7
      collector_ip_vpn: vpn1
      collector_description: Collector1
      provider: '{{ cli }}'

  - name: Configure flow sampling.
    community.network.ce_sflow:
      sflow_interface: 10GE2/0/2
      sample_collector: 1
      sample_direction: inbound
      provider: '{{ cli }}'

  - name: Configure counter sampling.
    community.network.ce_sflow:
      sflow_interface: 10GE2/0/2
      counter_collector: 1
      counter_interval: 1000
      provider: '{{ cli }}'

Return Values

Common return values are documented here, the following are the fields unique to this module:

Key	Returned	Description
changed boolean	always	check to see if a change was made on the device Sample: True
end_state dictionary	verbose mode	k/v pairs of configuration after module execution Sample: {'agent': {'family': 'ipv4', 'ipv4Addr': '1.2.3.4', 'ipv6Addr': None}}
existing dictionary	verbose mode	k/v pairs of existing configuration Sample: {'agent': {}}
proposed dictionary	verbose mode	k/v pairs of parameters passed into module Sample: {'agent_ip': '6.6.6.6', 'state': 'present'}
updates list / elements=string	always	commands sent to the device Sample: ['sflow agent ip 6.6.6.6']

Authors

QijunPan (@QijunPan)

© 2012–2018 Michael DeHaan
© 2018–2021 Red Hat, Inc.
Licensed under the GNU General Public License version 3.
https://docs.ansible.com/ansible/latest/collections/community/network/ce_sflow_module.html

Docs

Docs4dev

Title here