fortinet.fortios.fortios_wireless_controller_wtp_profile – Configure WTP profiles or FortiAP profiles that define radio settings for manageable FortiAP platforms in Fortinet’s FortiOS and FortiGate.
Note
This plugin is part of the fortinet.fortios collection (version 2.1.2).
You might already have this collection installed if you are using the ansible package. It is not included in ansible-core. To check whether it is installed, run ansible-galaxy collection list.
To install it, use: ansible-galaxy collection install fortinet.fortios.
To use it in a playbook, specify: fortinet.fortios.fortios_wireless_controller_wtp_profile.
New in version 2.10: of fortinet.fortios
Synopsis
- This module is able to configure a FortiGate or FortiOS (FOS) device by allowing the user to set and modify wireless_controller feature and wtp_profile category. Examples include all parameters and values need to be adjusted to datasources before usage. Tested with FOS v6.0.0
Requirements
The below requirements are needed on the host that executes this module.
- ansible>=2.9.0
Parameters
| Parameter | Choices/Defaults | Comments | |||
|---|---|---|---|---|---|
| access_token
string
|
Token-based authentication. Generated from GUI of Fortigate.
|
||||
| enable_log
boolean
|
|
Enable/Disable logging for task.
|
|||
| state
string / required
|
|
Indicates whether to create or remove the object.
|
|||
| vdom
string
|
Default:
"root"
|
Virtual domain, among those defined previously. A vdom is a virtual instance of the FortiGate that can be configured and used as a different unit.
|
|||
| wireless_controller_wtp_profile
dictionary
|
Configure WTP profiles or FortiAP profiles that define radio settings for manageable FortiAP platforms.
|
||||
| allowaccess
list / elements=string
|
|
Control management access to the managed WTP, FortiAP, or AP. Separate entries with a space.
|
|||
| ap_country
string
|
|
Country in which this WTP, FortiAP or AP will operate .
|
|||
| ap_handoff
string
|
|
Enable/disable AP handoff of clients to other APs .
|
|||
| apcfg_profile
string
|
AP local configuration profile name. Source wireless-controller.apcfg-profile.name.
|
||||
| ble_profile
string
|
Bluetooth Low Energy profile name. Source wireless-controller.ble-profile.name.
|
||||
| comment
string
|
Comment.
|
||||
| control_message_offload
list / elements=string
|
|
Enable/disable CAPWAP control message data channel offload.
|
|||
| deny_mac_list
list / elements=string
|
List of MAC addresses that are denied access to this WTP, FortiAP, or AP.
|
||||
| id
integer / required
|
ID.
|
||||
| mac
string
|
A WiFi device with this MAC address is denied access to this WTP, FortiAP or AP.
|
||||
| dtls_in_kernel
string
|
|
Enable/disable data channel DTLS in kernel.
|
|||
| dtls_policy
list / elements=string
|
|
WTP data channel DTLS policy .
|
|||
| energy_efficient_ethernet
string
|
|
Enable/disable use of energy efficient Ethernet on WTP.
|
|||
| ext_info_enable
string
|
|
Enable/disable station/VAP/radio extension information.
|
|||
| frequency_handoff
string
|
|
Enable/disable frequency handoff of clients to other channels .
|
|||
| handoff_roaming
string
|
|
Enable/disable client load balancing during roaming to avoid roaming delay .
|
|||
| handoff_rssi
integer
|
Minimum received signal strength indicator (RSSI) value for handoff (20 - 30).
|
||||
| handoff_sta_thresh
integer
|
Threshold value for AP handoff.
|
||||
| ip_fragment_preventing
list / elements=string
|
|
Select how to prevent IP fragmentation for CAPWAP tunneled control and data packets .
|
|||
| lan
dictionary
|
WTP LAN port mapping.
|
||||
| port1_mode
string
|
|
LAN port 1 mode.
|
|||
| port1_ssid
string
|
Bridge LAN port 1 to SSID. Source wireless-controller.vap.name.
|
||||
| port2_mode
string
|
|
LAN port 2 mode.
|
|||
| port2_ssid
string
|
Bridge LAN port 2 to SSID. Source wireless-controller.vap.name.
|
||||
| port3_mode
string
|
|
LAN port 3 mode.
|
|||
| port3_ssid
string
|
Bridge LAN port 3 to SSID. Source wireless-controller.vap.name.
|
||||
| port4_mode
string
|
|
LAN port 4 mode.
|
|||
| port4_ssid
string
|
Bridge LAN port 4 to SSID. Source wireless-controller.vap.name.
|
||||
| port5_mode
string
|
|
LAN port 5 mode.
|
|||
| port5_ssid
string
|
Bridge LAN port 5 to SSID. Source wireless-controller.vap.name.
|
||||
| port6_mode
string
|
|
LAN port 6 mode.
|
|||
| port6_ssid
string
|
Bridge LAN port 6 to SSID. Source wireless-controller.vap.name.
|
||||
| port7_mode
string
|
|
LAN port 7 mode.
|
|||
| port7_ssid
string
|
Bridge LAN port 7 to SSID. Source wireless-controller.vap.name.
|
||||
| port8_mode
string
|
|
LAN port 8 mode.
|
|||
| port8_ssid
string
|
Bridge LAN port 8 to SSID. Source wireless-controller.vap.name.
|
||||
| port_esl_mode
string
|
|
ESL port mode.
|
|||
| port_esl_ssid
string
|
Bridge ESL port to SSID. Source system.interface.name.
|
||||
| port_mode
string
|
|
LAN port mode.
|
|||
| port_ssid
string
|
Bridge LAN port to SSID. Source wireless-controller.vap.name.
|
||||
| lbs
dictionary
|
Set various location based service (LBS) options.
|
||||
| aeroscout
string
|
|
Enable/disable AeroScout Real Time Location Service (RTLS) support .
|
|||
| aeroscout_ap_mac
string
|
|
Use BSSID or board MAC address as AP MAC address in AeroScout AP messages .
|
|||
| aeroscout_mmu_report
string
|
|
Enable/disable compounded AeroScout tag and MU report .
|
|||
| aeroscout_mu
string
|
|
Enable/disable AeroScout Mobile Unit (MU) support .
|
|||
| aeroscout_mu_factor
integer
|
AeroScout MU mode dilution factor .
|
||||
| aeroscout_mu_timeout
integer
|
AeroScout MU mode timeout (0 - 65535 sec).
|
||||
| aeroscout_server_ip
string
|
IP address of AeroScout server.
|
||||
| aeroscout_server_port
integer
|
AeroScout server UDP listening port.
|
||||
| ekahau_blink_mode
string
|
|
Enable/disable Ekahau blink mode (now known as AiRISTA Flow) to track and locate WiFi tags .
|
|||
| ekahau_tag
string
|
WiFi frame MAC address or WiFi Tag.
|
||||
| erc_server_ip
string
|
IP address of Ekahau RTLS Controller (ERC).
|
||||
| erc_server_port
integer
|
Ekahau RTLS Controller (ERC) UDP listening port.
|
||||
| fortipresence
string
|
|
Enable/disable FortiPresence to monitor the location and activity of WiFi clients even if they don"t connect to this WiFi network .
|
|||
| fortipresence_ble
string
|
|
Enable/disable FortiPresence finding and reporting BLE devices.
|
|||
| fortipresence_frequency
integer
|
FortiPresence report transmit frequency (5 - 65535 sec).
|
||||
| fortipresence_port
integer
|
FortiPresence server UDP listening port .
|
||||
| fortipresence_project
string
|
FortiPresence project name (max. 16 characters).
|
||||
| fortipresence_rogue
string
|
|
Enable/disable FortiPresence finding and reporting rogue APs.
|
|||
| fortipresence_secret
string
|
FortiPresence secret password (max. 16 characters).
|
||||
| fortipresence_server
string
|
FortiPresence server IP address.
|
||||
| fortipresence_unassoc
string
|
|
Enable/disable FortiPresence finding and reporting unassociated stations.
|
|||
| station_locate
string
|
|
Enable/disable client station locating services for all clients, whether associated or not .
|
|||
| led_schedules
list / elements=string
|
Recurring firewall schedules for illuminating LEDs on the FortiAP. If led-state is enabled, LEDs will be visible when at least one of the schedules is valid. Separate multiple schedule names with a space.
|
||||
| name
string / required
|
LED schedule name. Source firewall.schedule.group.name firewall.schedule.recurring.name.
|
||||
| led_state
string
|
|
Enable/disable use of LEDs on WTP .
|
|||
| lldp
string
|
|
Enable/disable Link Layer Discovery Protocol (LLDP) for the WTP, FortiAP, or AP .
|
|||
| login_passwd
string
|
Set the managed WTP, FortiAP, or AP"s administrator password.
|
||||
| login_passwd_change
string
|
|
Change or reset the administrator password of a managed WTP, FortiAP or AP (yes, default, or no).
|
|||
| max_clients
integer
|
Maximum number of stations (STAs) supported by the WTP .
|
||||
| name
string / required
|
WTP (or FortiAP or AP) profile name.
|
||||
| platform
dictionary
|
WTP, FortiAP, or AP platform.
|
||||
| ddscan
string
|
|
Enable/disable use of one radio for dedicated dual-band scanning to detect RF characterization and wireless threat management.
|
|||
| mode
string
|
|
Configure operation mode of 5G radios .
|
|||
| type
string
|
|
WTP, FortiAP or AP platform type. There are built-in WTP profiles for all supported FortiAP models. You can select a built-in profile and customize it or create a new profile.
|
|||
| poe_mode
string
|
|
Set the WTP, FortiAP, or AP"s PoE mode.
|
|||
| radio_1
dictionary
|
Configuration options for radio 1.
|
||||
| airtime_fairness
string
|
|
Enable/disable airtime fairness .
|
|||
| amsdu
string
|
|
Enable/disable 802.11n AMSDU support. AMSDU can improve performance if supported by your WiFi clients .
|
|||
| ap_handoff
string
|
|
Enable/disable AP handoff of clients to other APs .
|
|||
| ap_sniffer_addr
string
|
MAC address to monitor.
|
||||
| ap_sniffer_bufsize
integer
|
Sniffer buffer size (1 - 32 MB).
|
||||
| ap_sniffer_chan
integer
|
Channel on which to operate the sniffer .
|
||||
| ap_sniffer_ctl
string
|
|
Enable/disable sniffer on WiFi control frame .
|
|||
| ap_sniffer_data
string
|
|
Enable/disable sniffer on WiFi data frame .
|
|||
| ap_sniffer_mgmt_beacon
string
|
|
Enable/disable sniffer on WiFi management Beacon frames .
|
|||
| ap_sniffer_mgmt_other
string
|
|
Enable/disable sniffer on WiFi management other frames .
|
|||
| ap_sniffer_mgmt_probe
string
|
|
Enable/disable sniffer on WiFi management probe frames .
|
|||
| auto_power_high
integer
|
Automatic transmit power high limit in dBm (the actual range of transmit power depends on the AP platform type).
|
||||
| auto_power_level
string
|
|
Enable/disable automatic power-level adjustment to prevent co-channel interference .
|
|||
| auto_power_low
integer
|
Automatic transmission power low limit in dBm (the actual range of transmit power depends on the AP platform type).
|
||||
| auto_power_target
string
|
The target of automatic transmit power adjustment in dBm. (-95 to -20).
|
||||
| band
string
|
|
WiFi band that Radio 1 operates on.
|
|||
| band_5g_type
string
|
|
WiFi 5G band type.
|
|||
| bandwidth_admission_control
string
|
|
Enable/disable WiFi multimedia (WMM) bandwidth admission control to optimize WiFi bandwidth use. A request to join the wireless network is only allowed if the access point has enough bandwidth to support it.
|
|||
| bandwidth_capacity
integer
|
Maximum bandwidth capacity allowed (1 - 600000 Kbps).
|
||||
| beacon_interval
integer
|
Beacon interval. The time between beacon frames in msec (the actual range of beacon interval depends on the AP platform type).
|
||||
| bss_color
integer
|
BSS color value for this 11ax radio (0 - 63, 0 means disable. ).
|
||||
| call_admission_control
string
|
|
Enable/disable WiFi multimedia (WMM) call admission control to optimize WiFi bandwidth use for VoIP calls. New VoIP calls are only accepted if there is enough bandwidth available to support them.
|
|||
| call_capacity
integer
|
Maximum number of Voice over WLAN (VoWLAN) phones supported by the radio (0 - 60).
|
||||
| channel
list / elements=string
|
Selected list of wireless radio channels.
|
||||
| chan
string / required
|
Channel number.
|
||||
| channel_bonding
string
|
|
Channel bandwidth: 80, 40, or 20MHz. Channels may use both 20 and 40 by enabling coexistence.
|
|||
| channel_utilization
string
|
|
Enable/disable measuring channel utilization.
|
|||
| coexistence
string
|
|
Enable/disable allowing both HT20 and HT40 on the same radio .
|
|||
| darrp
string
|
|
Enable/disable Distributed Automatic Radio Resource Provisioning (DARRP) to make sure the radio is always using the most optimal channel .
|
|||
| drma
string
|
|
Enable/disable dynamic radio mode assignment (DRMA) .
|
|||
| drma_sensitivity
string
|
|
Network Coverage Factor (NCF) percentage required to consider a radio as redundant .
|
|||
| dtim
integer
|
DTIM interval. The frequency to transmit Delivery Traffic Indication Message (or Map) (DTIM) messages (1 - 255). Set higher to save client battery life.
|
||||
| frag_threshold
integer
|
Maximum packet size that can be sent without fragmentation (800 - 2346 bytes).
|
||||
| frequency_handoff
string
|
|
Enable/disable frequency handoff of clients to other channels .
|
|||
| iperf_protocol
string
|
|
Iperf test protocol .
|
|||
| iperf_server_port
integer
|
Iperf service port number.
|
||||
| max_clients
integer
|
Maximum number of stations (STAs) or WiFi clients supported by the radio. Range depends on the hardware.
|
||||
| max_distance
integer
|
Maximum expected distance between the AP and clients (0 - 54000 m).
|
||||
| mode
string
|
|
Mode of radio 1. Radio 1 can be disabled, configured as an access point, a rogue AP monitor, or a sniffer.
|
|||
| power_level
integer
|
Radio power level as a percentage of the maximum transmit power (0 - 100).
|
||||
| power_mode
string
|
|
Set radio effective isotropic radiated power (EIRP) in dBm or by a percentage of the maximum EIRP . This power takes into account both radio transmit power and antenna gain. Higher power level settings may be constrained by local regulatory requirements and AP capabilities.
|
|||
| power_value
integer
|
Radio EIRP power in dBm (1 - 33).
|
||||
| powersave_optimize
string
|
|
Enable client power-saving features such as TIM, AC VO, and OBSS etc.
|
|||
| protection_mode
string
|
|
Enable/disable 802.11g protection modes to support backwards compatibility with older clients (rtscts, ctsonly, disable).
|
|||
| radio_id
integer
|
radio-id
|
||||
| rts_threshold
integer
|
Maximum packet size for RTS transmissions, specifying the maximum size of a data packet before RTS/CTS (256 - 2346 bytes).
|
||||
| sam_bssid
string
|
BSSID for WiFi network.
|
||||
| sam_captive_portal
string
|
|
Enable/disable Captive Portal Authentication .
|
|||
| sam_password
string
|
Passphrase for WiFi network connection.
|
||||
| sam_report_intv
integer
|
SAM report interval (sec), 0 for a one-time report.
|
||||
| sam_security_type
string
|
|
Select WiFi network security type .
|
|||
| sam_server
string
|
SAM test server IP address or domain name.
|
||||
| sam_ssid
string
|
SSID for WiFi network.
|
||||
| sam_test
string
|
|
Select SAM test type .
|
|||
| sam_username
string
|
Username for WiFi network connection.
|
||||
| short_guard_interval
string
|
|
Use either the short guard interval (Short GI) of 400 ns or the long guard interval (Long GI) of 800 ns.
|
|||
| spectrum_analysis
string
|
|
Enable/disable spectrum analysis to find interference that would negatively impact wireless performance.
|
|||
| transmit_optimize
string
|
|
Packet transmission optimization options including power saving, aggregation limiting, retry limiting, etc. All are enabled by default.
|
|||
| vap_all
string
|
|
Enable/disable the automatic inheritance of all Virtual Access Points (VAPs) .
|
|||
| vaps
list / elements=string
|
Manually selected list of Virtual Access Points (VAPs).
|
||||
| name
string / required
|
Virtual Access Point (VAP) name. Source wireless-controller.vap-group.name wireless-controller.vap.name.
|
||||
| wids_profile
string
|
Wireless Intrusion Detection System (WIDS) profile name to assign to the radio. Source wireless-controller.wids-profile.name.
|
||||
| zero_wait_dfs
string
|
|
Enable/disable zero wait DFS on radio .
|
|||
| radio_2
dictionary
|
Configuration options for radio 2.
|
||||
| airtime_fairness
string
|
|
Enable/disable airtime fairness .
|
|||
| amsdu
string
|
|
Enable/disable 802.11n AMSDU support. AMSDU can improve performance if supported by your WiFi clients .
|
|||
| ap_handoff
string
|
|
Enable/disable AP handoff of clients to other APs .
|
|||
| ap_sniffer_addr
string
|
MAC address to monitor.
|
||||
| ap_sniffer_bufsize
integer
|
Sniffer buffer size (1 - 32 MB).
|
||||
| ap_sniffer_chan
integer
|
Channel on which to operate the sniffer .
|
||||
| ap_sniffer_ctl
string
|
|
Enable/disable sniffer on WiFi control frame .
|
|||
| ap_sniffer_data
string
|
|
Enable/disable sniffer on WiFi data frame .
|
|||
| ap_sniffer_mgmt_beacon
string
|
|
Enable/disable sniffer on WiFi management Beacon frames .
|
|||
| ap_sniffer_mgmt_other
string
|
|
Enable/disable sniffer on WiFi management other frames .
|
|||
| ap_sniffer_mgmt_probe
string
|
|
Enable/disable sniffer on WiFi management probe frames .
|
|||
| auto_power_high
integer
|
Automatic transmit power high limit in dBm (the actual range of transmit power depends on the AP platform type).
|
||||
| auto_power_level
string
|
|
Enable/disable automatic power-level adjustment to prevent co-channel interference .
|
|||
| auto_power_low
integer
|
Automatic transmission power low limit in dBm (the actual range of transmit power depends on the AP platform type).
|
||||
| auto_power_target
string
|
The target of automatic transmit power adjustment in dBm. (-95 to -20).
|
||||
| band
string
|
|
WiFi band that Radio 2 operates on.
|
|||
| band_5g_type
string
|
|
WiFi 5G band type.
|
|||
| bandwidth_admission_control
string
|
|
Enable/disable WiFi multimedia (WMM) bandwidth admission control to optimize WiFi bandwidth use. A request to join the wireless network is only allowed if the access point has enough bandwidth to support it.
|
|||
| bandwidth_capacity
integer
|
Maximum bandwidth capacity allowed (1 - 600000 Kbps).
|
||||
| beacon_interval
integer
|
Beacon interval. The time between beacon frames in msec (the actual range of beacon interval depends on the AP platform type).
|
||||
| bss_color
integer
|
BSS color value for this 11ax radio (0 - 63, 0 means disable. ).
|
||||
| call_admission_control
string
|
|
Enable/disable WiFi multimedia (WMM) call admission control to optimize WiFi bandwidth use for VoIP calls. New VoIP calls are only accepted if there is enough bandwidth available to support them.
|
|||
| call_capacity
integer
|
Maximum number of Voice over WLAN (VoWLAN) phones supported by the radio (0 - 60).
|
||||
| channel
list / elements=string
|
Selected list of wireless radio channels.
|
||||
| chan
string / required
|
Channel number.
|
||||
| channel_bonding
string
|
|
Channel bandwidth: 80, 40, or 20MHz. Channels may use both 20 and 40 by enabling coexistence.
|
|||
| channel_utilization
string
|
|
Enable/disable measuring channel utilization.
|
|||
| coexistence
string
|
|
Enable/disable allowing both HT20 and HT40 on the same radio .
|
|||
| darrp
string
|
|
Enable/disable Distributed Automatic Radio Resource Provisioning (DARRP) to make sure the radio is always using the most optimal channel .
|
|||
| drma
string
|
|
Enable/disable dynamic radio mode assignment (DRMA) .
|
|||
| drma_sensitivity
string
|
|
Network Coverage Factor (NCF) percentage required to consider a radio as redundant .
|
|||
| dtim
integer
|
DTIM interval. The frequency to transmit Delivery Traffic Indication Message (or Map) (DTIM) messages (1 - 255). Set higher to save client battery life.
|
||||
| frag_threshold
integer
|
Maximum packet size that can be sent without fragmentation (800 - 2346 bytes).
|
||||
| frequency_handoff
string
|
|
Enable/disable frequency handoff of clients to other channels .
|
|||
| iperf_protocol
string
|
|
Iperf test protocol .
|
|||
| iperf_server_port
integer
|
Iperf service port number.
|
||||
| max_clients
integer
|
Maximum number of stations (STAs) or WiFi clients supported by the radio. Range depends on the hardware.
|
||||
| max_distance
integer
|
Maximum expected distance between the AP and clients (0 - 54000 m).
|
||||
| mode
string
|
|
Mode of radio 2. Radio 2 can be disabled, configured as an access point, a rogue AP monitor, or a sniffer.
|
|||
| power_level
integer
|
Radio power level as a percentage of the maximum transmit power (0 - 100).
|
||||
| power_mode
string
|
|
Set radio effective isotropic radiated power (EIRP) in dBm or by a percentage of the maximum EIRP . This power takes into account both radio transmit power and antenna gain. Higher power level settings may be constrained by local regulatory requirements and AP capabilities.
|
|||
| power_value
integer
|
Radio EIRP power in dBm (1 - 33).
|
||||
| powersave_optimize
string
|
|
Enable client power-saving features such as TIM, AC VO, and OBSS etc.
|
|||
| protection_mode
string
|
|
Enable/disable 802.11g protection modes to support backwards compatibility with older clients (rtscts, ctsonly, disable).
|
|||
| radio_id
integer
|
radio-id
|
||||
| rts_threshold
integer
|
Maximum packet size for RTS transmissions, specifying the maximum size of a data packet before RTS/CTS (256 - 2346 bytes).
|
||||
| sam_bssid
string
|
BSSID for WiFi network.
|
||||
| sam_captive_portal
string
|
|
Enable/disable Captive Portal Authentication .
|
|||
| sam_password
string
|
Passphrase for WiFi network connection.
|
||||
| sam_report_intv
integer
|
SAM report interval (sec), 0 for a one-time report.
|
||||
| sam_security_type
string
|
|
Select WiFi network security type .
|
|||
| sam_server
string
|
SAM test server IP address or domain name.
|
||||
| sam_ssid
string
|
SSID for WiFi network.
|
||||
| sam_test
string
|
|
Select SAM test type .
|
|||
| sam_username
string
|
Username for WiFi network connection.
|
||||
| short_guard_interval
string
|
|
Use either the short guard interval (Short GI) of 400 ns or the long guard interval (Long GI) of 800 ns.
|
|||
| spectrum_analysis
string
|
|
Enable/disable spectrum analysis to find interference that would negatively impact wireless performance.
|
|||
| transmit_optimize
string
|
|
Packet transmission optimization options including power saving, aggregation limiting, retry limiting, etc. All are enabled by default.
|
|||
| vap_all
string
|
|
Enable/disable the automatic inheritance of all Virtual Access Points (VAPs) .
|
|||
| vaps
list / elements=string
|
Manually selected list of Virtual Access Points (VAPs).
|
||||
| name
string / required
|
Virtual Access Point (VAP) name. Source wireless-controller.vap-group.name wireless-controller.vap.name.
|
||||
| wids_profile
string
|
Wireless Intrusion Detection System (WIDS) profile name to assign to the radio. Source wireless-controller.wids-profile.name.
|
||||
| zero_wait_dfs
string
|
|
Enable/disable zero wait DFS on radio .
|
|||
| radio_3
dictionary
|
Configuration options for radio 3.
|
||||
| airtime_fairness
string
|
|
Enable/disable airtime fairness .
|
|||
| amsdu
string
|
|
Enable/disable 802.11n AMSDU support. AMSDU can improve performance if supported by your WiFi clients .
|
|||
| ap_handoff
string
|
|
Enable/disable AP handoff of clients to other APs .
|
|||
| ap_sniffer_addr
string
|
MAC address to monitor.
|
||||
| ap_sniffer_bufsize
integer
|
Sniffer buffer size (1 - 32 MB).
|
||||
| ap_sniffer_chan
integer
|
Channel on which to operate the sniffer .
|
||||
| ap_sniffer_ctl
string
|
|
Enable/disable sniffer on WiFi control frame .
|
|||
| ap_sniffer_data
string
|
|
Enable/disable sniffer on WiFi data frame .
|
|||
| ap_sniffer_mgmt_beacon
string
|
|
Enable/disable sniffer on WiFi management Beacon frames .
|
|||
| ap_sniffer_mgmt_other
string
|
|
Enable/disable sniffer on WiFi management other frames .
|
|||
| ap_sniffer_mgmt_probe
string
|
|
Enable/disable sniffer on WiFi management probe frames .
|
|||
| auto_power_high
integer
|
The upper bound of automatic transmit power adjustment in dBm (the actual range of transmit power depends on the AP platform type).
|
||||
| auto_power_level
string
|
|
Enable/disable automatic power-level adjustment to prevent co-channel interference .
|
|||
| auto_power_low
integer
|
The lower bound of automatic transmit power adjustment in dBm (the actual range of transmit power depends on the AP platform type).
|
||||
| auto_power_target
string
|
The target of automatic transmit power adjustment in dBm. (-95 to -20).
|
||||
| band
string
|
|
WiFi band that Radio 3 operates on.
|
|||
| band_5g_type
string
|
|
WiFi 5G band type.
|
|||
| bandwidth_admission_control
string
|
|
Enable/disable WiFi multimedia (WMM) bandwidth admission control to optimize WiFi bandwidth use. A request to join the wireless network is only allowed if the access point has enough bandwidth to support it.
|
|||
| bandwidth_capacity
integer
|
Maximum bandwidth capacity allowed (1 - 600000 Kbps).
|
||||
| beacon_interval
integer
|
Beacon interval. The time between beacon frames in msec (the actual range of beacon interval depends on the AP platform type).
|
||||
| bss_color
integer
|
BSS color value for this 11ax radio (0 - 63, 0 means disable. ).
|
||||
| call_admission_control
string
|
|
Enable/disable WiFi multimedia (WMM) call admission control to optimize WiFi bandwidth use for VoIP calls. New VoIP calls are only accepted if there is enough bandwidth available to support them.
|
|||
| call_capacity
integer
|
Maximum number of Voice over WLAN (VoWLAN) phones supported by the radio (0 - 60).
|
||||
| channel
list / elements=string
|
Selected list of wireless radio channels.
|
||||
| chan
string / required
|
Channel number.
|
||||
| channel_bonding
string
|
|
Channel bandwidth: 160,80, 40, or 20MHz. Channels may use both 20 and 40 by enabling coexistence.
|
|||
| channel_utilization
string
|
|
Enable/disable measuring channel utilization.
|
|||
| coexistence
string
|
|
Enable/disable allowing both HT20 and HT40 on the same radio .
|
|||
| darrp
string
|
|
Enable/disable Distributed Automatic Radio Resource Provisioning (DARRP) to make sure the radio is always using the most optimal channel .
|
|||
| drma
string
|
|
Enable/disable dynamic radio mode assignment (DRMA) .
|
|||
| drma_sensitivity
string
|
|
Network Coverage Factor (NCF) percentage required to consider a radio as redundant .
|
|||
| dtim
integer
|
Delivery Traffic Indication Map (DTIM) period (1 - 255). Set higher to save battery life of WiFi client in power-save mode.
|
||||
| frag_threshold
integer
|
Maximum packet size that can be sent without fragmentation (800 - 2346 bytes).
|
||||
| frequency_handoff
string
|
|
Enable/disable frequency handoff of clients to other channels .
|
|||
| iperf_protocol
string
|
|
Iperf test protocol .
|
|||
| iperf_server_port
integer
|
Iperf service port number.
|
||||
| max_clients
integer
|
Maximum number of stations (STAs) or WiFi clients supported by the radio. Range depends on the hardware.
|
||||
| max_distance
integer
|
Maximum expected distance between the AP and clients (0 - 54000 m).
|
||||
| mode
string
|
|
Mode of radio 3. Radio 3 can be disabled, configured as an access point, a rogue AP monitor, or a sniffer.
|
|||
| power_level
integer
|
Radio power level as a percentage of the maximum transmit power (0 - 100).
|
||||
| power_mode
string
|
|
Set radio effective isotropic radiated power (EIRP) in dBm or by a percentage of the maximum EIRP . This power takes into account both radio transmit power and antenna gain. Higher power level settings may be constrained by local regulatory requirements and AP capabilities.
|
|||
| power_value
integer
|
Radio EIRP power in dBm (1 - 33).
|
||||
| powersave_optimize
string
|
|
Enable client power-saving features such as TIM, AC VO, and OBSS etc.
|
|||
| protection_mode
string
|
|
Enable/disable 802.11g protection modes to support backwards compatibility with older clients (rtscts, ctsonly, disable).
|
|||
| radio_id
integer
|
radio-id
|
||||
| rts_threshold
integer
|
Maximum packet size for RTS transmissions, specifying the maximum size of a data packet before RTS/CTS (256 - 2346 bytes).
|
||||
| sam_bssid
string
|
BSSID for WiFi network.
|
||||
| sam_captive_portal
string
|
|
Enable/disable Captive Portal Authentication .
|
|||
| sam_password
string
|
Passphrase for WiFi network connection.
|
||||
| sam_report_intv
integer
|
SAM report interval (sec), 0 for a one-time report.
|
||||
| sam_security_type
string
|
|
Select WiFi network security type .
|
|||
| sam_server
string
|
SAM test server IP address or domain name.
|
||||
| sam_ssid
string
|
SSID for WiFi network.
|
||||
| sam_test
string
|
|
Select SAM test type .
|
|||
| sam_username
string
|
Username for WiFi network connection.
|
||||
| short_guard_interval
string
|
|
Use either the short guard interval (Short GI) of 400 ns or the long guard interval (Long GI) of 800 ns.
|
|||
| spectrum_analysis
string
|
|
Enable/disable spectrum analysis to find interference that would negatively impact wireless performance.
|
|||
| transmit_optimize
string
|
|
Packet transmission optimization options including power saving, aggregation limiting, retry limiting, etc. All are enabled by default.
|
|||
| vap_all
string
|
|
Enable/disable the automatic inheritance of all Virtual Access Points (VAPs) .
|
|||
| vaps
list / elements=string
|
Manually selected list of Virtual Access Points (VAPs).
|
||||
| name
string / required
|
Virtual Access Point (VAP) name. Source wireless-controller.vap-group.name system.interface.name.
|
||||
| wids_profile
string
|
Wireless Intrusion Detection System (WIDS) profile name to assign to the radio. Source wireless-controller.wids-profile.name.
|
||||
| zero_wait_dfs
string
|
|
Enable/disable zero wait DFS on radio .
|
|||
| radio_4
dictionary
|
Configuration options for radio 4.
|
||||
| airtime_fairness
string
|
|
Enable/disable airtime fairness .
|
|||
| amsdu
string
|
|
Enable/disable 802.11n AMSDU support. AMSDU can improve performance if supported by your WiFi clients .
|
|||
| ap_handoff
string
|
|
Enable/disable AP handoff of clients to other APs .
|
|||
| ap_sniffer_addr
string
|
MAC address to monitor.
|
||||
| ap_sniffer_bufsize
integer
|
Sniffer buffer size (1 - 32 MB).
|
||||
| ap_sniffer_chan
integer
|
Channel on which to operate the sniffer .
|
||||
| ap_sniffer_ctl
string
|
|
Enable/disable sniffer on WiFi control frame .
|
|||
| ap_sniffer_data
string
|
|
Enable/disable sniffer on WiFi data frame .
|
|||
| ap_sniffer_mgmt_beacon
string
|
|
Enable/disable sniffer on WiFi management Beacon frames .
|
|||
| ap_sniffer_mgmt_other
string
|
|
Enable/disable sniffer on WiFi management other frames .
|
|||
| ap_sniffer_mgmt_probe
string
|
|
Enable/disable sniffer on WiFi management probe frames .
|
|||
| auto_power_high
integer
|
The upper bound of automatic transmit power adjustment in dBm (the actual range of transmit power depends on the AP platform type).
|
||||
| auto_power_level
string
|
|
Enable/disable automatic power-level adjustment to prevent co-channel interference .
|
|||
| auto_power_low
integer
|
The lower bound of automatic transmit power adjustment in dBm (the actual range of transmit power depends on the AP platform type).
|
||||
| auto_power_target
string
|
The target of automatic transmit power adjustment in dBm. (-95 to -20).
|
||||
| band
string
|
|
WiFi band that Radio 3 operates on.
|
|||
| band_5g_type
string
|
|
WiFi 5G band type.
|
|||
| bandwidth_admission_control
string
|
|
Enable/disable WiFi multimedia (WMM) bandwidth admission control to optimize WiFi bandwidth use. A request to join the wireless network is only allowed if the access point has enough bandwidth to support it.
|
|||
| bandwidth_capacity
integer
|
Maximum bandwidth capacity allowed (1 - 600000 Kbps).
|
||||
| beacon_interval
integer
|
Beacon interval. The time between beacon frames in msec (the actual range of beacon interval depends on the AP platform type).
|
||||
| bss_color
integer
|
BSS color value for this 11ax radio (0 - 63, 0 means disable. ).
|
||||
| call_admission_control
string
|
|
Enable/disable WiFi multimedia (WMM) call admission control to optimize WiFi bandwidth use for VoIP calls. New VoIP calls are only accepted if there is enough bandwidth available to support them.
|
|||
| call_capacity
integer
|
Maximum number of Voice over WLAN (VoWLAN) phones supported by the radio (0 - 60).
|
||||
| channel
list / elements=string
|
Selected list of wireless radio channels.
|
||||
| chan
string / required
|
Channel number.
|
||||
| channel_bonding
string
|
|
Channel bandwidth: 160,80, 40, or 20MHz. Channels may use both 20 and 40 by enabling coexistence.
|
|||
| channel_utilization
string
|
|
Enable/disable measuring channel utilization.
|
|||
| coexistence
string
|
|
Enable/disable allowing both HT20 and HT40 on the same radio .
|
|||
| darrp
string
|
|
Enable/disable Distributed Automatic Radio Resource Provisioning (DARRP) to make sure the radio is always using the most optimal channel .
|
|||
| drma
string
|
|
Enable/disable dynamic radio mode assignment (DRMA) .
|
|||
| drma_sensitivity
string
|
|
Network Coverage Factor (NCF) percentage required to consider a radio as redundant .
|
|||
| dtim
integer
|
Delivery Traffic Indication Map (DTIM) period (1 - 255). Set higher to save battery life of WiFi client in power-save mode.
|
||||
| frag_threshold
integer
|
Maximum packet size that can be sent without fragmentation (800 - 2346 bytes).
|
||||
| frequency_handoff
string
|
|
Enable/disable frequency handoff of clients to other channels .
|
|||
| iperf_protocol
string
|
|
Iperf test protocol .
|
|||
| iperf_server_port
integer
|
Iperf service port number.
|
||||
| max_clients
integer
|
Maximum number of stations (STAs) or WiFi clients supported by the radio. Range depends on the hardware.
|
||||
| max_distance
integer
|
Maximum expected distance between the AP and clients (0 - 54000 m).
|
||||
| mode
string
|
|
Mode of radio 3. Radio 3 can be disabled, configured as an access point, a rogue AP monitor, or a sniffer.
|
|||
| power_level
integer
|
Radio power level as a percentage of the maximum transmit power (0 - 100).
|
||||
| power_mode
string
|
|
Set radio effective isotropic radiated power (EIRP) in dBm or by a percentage of the maximum EIRP . This power takes into account both radio transmit power and antenna gain. Higher power level settings may be constrained by local regulatory requirements and AP capabilities.
|
|||
| power_value
integer
|
Radio EIRP power in dBm (1 - 33).
|
||||
| powersave_optimize
string
|
|
Enable client power-saving features such as TIM, AC VO, and OBSS etc.
|
|||
| protection_mode
string
|
|
Enable/disable 802.11g protection modes to support backwards compatibility with older clients (rtscts, ctsonly, disable).
|
|||
| rts_threshold
integer
|
Maximum packet size for RTS transmissions, specifying the maximum size of a data packet before RTS/CTS (256 - 2346 bytes).
|
||||
| sam_bssid
string
|
BSSID for WiFi network.
|
||||
| sam_captive_portal
string
|
|
Enable/disable Captive Portal Authentication .
|
|||
| sam_password
string
|
Passphrase for WiFi network connection.
|
||||
| sam_report_intv
integer
|
SAM report interval (sec), 0 for a one-time report.
|
||||
| sam_security_type
string
|
|
Select WiFi network security type .
|
|||
| sam_server
string
|
SAM test server IP address or domain name.
|
||||
| sam_ssid
string
|
SSID for WiFi network.
|
||||
| sam_test
string
|
|
Select SAM test type .
|
|||
| sam_username
string
|
Username for WiFi network connection.
|
||||
| short_guard_interval
string
|
|
Use either the short guard interval (Short GI) of 400 ns or the long guard interval (Long GI) of 800 ns.
|
|||
| spectrum_analysis
string
|
|
Enable/disable spectrum analysis to find interference that would negatively impact wireless performance.
|
|||
| transmit_optimize
string
|
|
Packet transmission optimization options including power saving, aggregation limiting, retry limiting, etc. All are enabled by default.
|
|||
| vap_all
string
|
|
Enable/disable the automatic inheritance of all Virtual Access Points (VAPs) .
|
|||
| vaps
list / elements=string
|
Manually selected list of Virtual Access Points (VAPs).
|
||||
| name
string / required
|
Virtual Access Point (VAP) name. Source wireless-controller.vap-group.name system.interface.name.
|
||||
| wids_profile
string
|
Wireless Intrusion Detection System (WIDS) profile name to assign to the radio. Source wireless-controller.wids-profile.name.
|
||||
| zero_wait_dfs
string
|
|
Enable/disable zero wait DFS on radio .
|
|||
| split_tunneling_acl
list / elements=string
|
Split tunneling ACL filter list.
|
||||
| dest_ip
string
|
Destination IP and mask for the split-tunneling subnet.
|
||||
| id
integer / required
|
ID.
|
||||
| split_tunneling_acl_local_ap_subnet
string
|
|
Enable/disable automatically adding local subnetwork of FortiAP to split-tunneling ACL .
|
|||
| split_tunneling_acl_path
string
|
|
Split tunneling ACL path is local/tunnel.
|
|||
| tun_mtu_downlink
integer
|
Downlink CAPWAP tunnel MTU (0, 576, or 1500 bytes).
|
||||
| tun_mtu_uplink
integer
|
Uplink CAPWAP tunnel MTU (0, 576, or 1500 bytes).
|
||||
| wan_port_mode
string
|
|
Enable/disable using a WAN port as a LAN port.
|
|||
Notes
Note
- Legacy fortiosapi has been deprecated, httpapi is the preferred way to run playbooks
Examples
- hosts: fortigates
collections:
- fortinet.fortios
connection: httpapi
vars:
vdom: "root"
ansible_httpapi_use_ssl: yes
ansible_httpapi_validate_certs: no
ansible_httpapi_port: 443
tasks:
- name: Configure WTP profiles or FortiAP profiles that define radio settings for manageable FortiAP platforms.
fortios_wireless_controller_wtp_profile:
vdom: "{{ vdom }}"
state: "present"
access_token: "<your_own_value>"
wireless_controller_wtp_profile:
allowaccess: "telnet"
ap_country: "NA"
ap_handoff: "enable"
apcfg_profile: "<your_own_value> (source wireless-controller.apcfg-profile.name)"
ble_profile: "<your_own_value> (source wireless-controller.ble-profile.name)"
comment: "Comment."
control_message_offload: "ebp-frame"
deny_mac_list:
-
id: "11"
mac: "<your_own_value>"
dtls_in_kernel: "enable"
dtls_policy: "clear-text"
energy_efficient_ethernet: "enable"
ext_info_enable: "enable"
frequency_handoff: "enable"
handoff_roaming: "enable"
handoff_rssi: "19"
handoff_sta_thresh: "20"
ip_fragment_preventing: "tcp-mss-adjust"
lan:
port_esl_mode: "offline"
port_esl_ssid: "<your_own_value> (source system.interface.name)"
port_mode: "offline"
port_ssid: "<your_own_value> (source wireless-controller.vap.name)"
port1_mode: "offline"
port1_ssid: "<your_own_value> (source wireless-controller.vap.name)"
port2_mode: "offline"
port2_ssid: "<your_own_value> (source wireless-controller.vap.name)"
port3_mode: "offline"
port3_ssid: "<your_own_value> (source wireless-controller.vap.name)"
port4_mode: "offline"
port4_ssid: "<your_own_value> (source wireless-controller.vap.name)"
port5_mode: "offline"
port5_ssid: "<your_own_value> (source wireless-controller.vap.name)"
port6_mode: "offline"
port6_ssid: "<your_own_value> (source wireless-controller.vap.name)"
port7_mode: "offline"
port7_ssid: "<your_own_value> (source wireless-controller.vap.name)"
port8_mode: "offline"
port8_ssid: "<your_own_value> (source wireless-controller.vap.name)"
lbs:
aeroscout: "enable"
aeroscout_ap_mac: "bssid"
aeroscout_mmu_report: "enable"
aeroscout_mu: "enable"
aeroscout_mu_factor: "48"
aeroscout_mu_timeout: "49"
aeroscout_server_ip: "<your_own_value>"
aeroscout_server_port: "51"
ekahau_blink_mode: "enable"
ekahau_tag: "<your_own_value>"
erc_server_ip: "<your_own_value>"
erc_server_port: "55"
fortipresence: "foreign"
fortipresence_ble: "enable"
fortipresence_frequency: "58"
fortipresence_port: "59"
fortipresence_project: "<your_own_value>"
fortipresence_rogue: "enable"
fortipresence_secret: "<your_own_value>"
fortipresence_server: "<your_own_value>"
fortipresence_unassoc: "enable"
station_locate: "enable"
led_schedules:
-
name: "default_name_67 (source firewall.schedule.group.name firewall.schedule.recurring.name)"
led_state: "enable"
lldp: "enable"
login_passwd: "<your_own_value>"
login_passwd_change: "yes"
max_clients: "72"
name: "default_name_73"
platform:
ddscan: "enable"
mode: "single-5G"
type: "AP-11N"
poe_mode: "auto"
radio_1:
airtime_fairness: "enable"
amsdu: "enable"
ap_handoff: "enable"
ap_sniffer_addr: "<your_own_value>"
ap_sniffer_bufsize: "84"
ap_sniffer_chan: "85"
ap_sniffer_ctl: "enable"
ap_sniffer_data: "enable"
ap_sniffer_mgmt_beacon: "enable"
ap_sniffer_mgmt_other: "enable"
ap_sniffer_mgmt_probe: "enable"
auto_power_high: "91"
auto_power_level: "enable"
auto_power_low: "93"
auto_power_target: "<your_own_value>"
band: "802.11a"
band_5g_type: "5g-full"
bandwidth_admission_control: "enable"
bandwidth_capacity: "98"
beacon_interval: "99"
bss_color: "100"
call_admission_control: "enable"
call_capacity: "102"
channel:
-
chan: "<your_own_value>"
channel_bonding: "80MHz"
channel_utilization: "enable"
coexistence: "enable"
darrp: "enable"
drma: "disable"
drma_sensitivity: "low"
dtim: "111"
frag_threshold: "112"
frequency_handoff: "enable"
iperf_protocol: "udp"
iperf_server_port: "115"
max_clients: "116"
max_distance: "117"
mode: "disabled"
power_level: "119"
power_mode: "dBm"
power_value: "121"
powersave_optimize: "tim"
protection_mode: "rtscts"
radio_id: "124"
rts_threshold: "125"
sam_bssid: "<your_own_value>"
sam_captive_portal: "enable"
sam_password: "<your_own_value>"
sam_report_intv: "129"
sam_security_type: "open"
sam_server: "<your_own_value>"
sam_ssid: "<your_own_value>"
sam_test: "ping"
sam_username: "<your_own_value>"
short_guard_interval: "enable"
spectrum_analysis: "enable"
transmit_optimize: "disable"
vap_all: "enable"
vaps:
-
name: "default_name_140 (source wireless-controller.vap-group.name wireless-controller.vap.name)"
wids_profile: "<your_own_value> (source wireless-controller.wids-profile.name)"
zero_wait_dfs: "enable"
radio_2:
airtime_fairness: "enable"
amsdu: "enable"
ap_handoff: "enable"
ap_sniffer_addr: "<your_own_value>"
ap_sniffer_bufsize: "148"
ap_sniffer_chan: "149"
ap_sniffer_ctl: "enable"
ap_sniffer_data: "enable"
ap_sniffer_mgmt_beacon: "enable"
ap_sniffer_mgmt_other: "enable"
ap_sniffer_mgmt_probe: "enable"
auto_power_high: "155"
auto_power_level: "enable"
auto_power_low: "157"
auto_power_target: "<your_own_value>"
band: "802.11a"
band_5g_type: "5g-full"
bandwidth_admission_control: "enable"
bandwidth_capacity: "162"
beacon_interval: "163"
bss_color: "164"
call_admission_control: "enable"
call_capacity: "166"
channel:
-
chan: "<your_own_value>"
channel_bonding: "80MHz"
channel_utilization: "enable"
coexistence: "enable"
darrp: "enable"
drma: "disable"
drma_sensitivity: "low"
dtim: "175"
frag_threshold: "176"
frequency_handoff: "enable"
iperf_protocol: "udp"
iperf_server_port: "179"
max_clients: "180"
max_distance: "181"
mode: "disabled"
power_level: "183"
power_mode: "dBm"
power_value: "185"
powersave_optimize: "tim"
protection_mode: "rtscts"
radio_id: "188"
rts_threshold: "189"
sam_bssid: "<your_own_value>"
sam_captive_portal: "enable"
sam_password: "<your_own_value>"
sam_report_intv: "193"
sam_security_type: "open"
sam_server: "<your_own_value>"
sam_ssid: "<your_own_value>"
sam_test: "ping"
sam_username: "<your_own_value>"
short_guard_interval: "enable"
spectrum_analysis: "enable"
transmit_optimize: "disable"
vap_all: "enable"
vaps:
-
name: "default_name_204 (source wireless-controller.vap-group.name wireless-controller.vap.name)"
wids_profile: "<your_own_value> (source wireless-controller.wids-profile.name)"
zero_wait_dfs: "enable"
radio_3:
airtime_fairness: "enable"
amsdu: "enable"
ap_handoff: "enable"
ap_sniffer_addr: "<your_own_value>"
ap_sniffer_bufsize: "212"
ap_sniffer_chan: "213"
ap_sniffer_ctl: "enable"
ap_sniffer_data: "enable"
ap_sniffer_mgmt_beacon: "enable"
ap_sniffer_mgmt_other: "enable"
ap_sniffer_mgmt_probe: "enable"
auto_power_high: "219"
auto_power_level: "enable"
auto_power_low: "221"
auto_power_target: "<your_own_value>"
band: "802.11a"
band_5g_type: "5g-full"
bandwidth_admission_control: "enable"
bandwidth_capacity: "226"
beacon_interval: "227"
bss_color: "228"
call_admission_control: "enable"
call_capacity: "230"
channel:
-
chan: "<your_own_value>"
channel_bonding: "160MHz"
channel_utilization: "enable"
coexistence: "enable"
darrp: "enable"
drma: "disable"
drma_sensitivity: "low"
dtim: "239"
frag_threshold: "240"
frequency_handoff: "enable"
iperf_protocol: "udp"
iperf_server_port: "243"
max_clients: "244"
max_distance: "245"
mode: "disabled"
power_level: "247"
power_mode: "dBm"
power_value: "249"
powersave_optimize: "tim"
protection_mode: "rtscts"
radio_id: "252"
rts_threshold: "253"
sam_bssid: "<your_own_value>"
sam_captive_portal: "enable"
sam_password: "<your_own_value>"
sam_report_intv: "257"
sam_security_type: "open"
sam_server: "<your_own_value>"
sam_ssid: "<your_own_value>"
sam_test: "ping"
sam_username: "<your_own_value>"
short_guard_interval: "enable"
spectrum_analysis: "enable"
transmit_optimize: "disable"
vap_all: "enable"
vaps:
-
name: "default_name_268 (source wireless-controller.vap-group.name system.interface.name)"
wids_profile: "<your_own_value> (source wireless-controller.wids-profile.name)"
zero_wait_dfs: "enable"
radio_4:
airtime_fairness: "enable"
amsdu: "enable"
ap_handoff: "enable"
ap_sniffer_addr: "<your_own_value>"
ap_sniffer_bufsize: "276"
ap_sniffer_chan: "277"
ap_sniffer_ctl: "enable"
ap_sniffer_data: "enable"
ap_sniffer_mgmt_beacon: "enable"
ap_sniffer_mgmt_other: "enable"
ap_sniffer_mgmt_probe: "enable"
auto_power_high: "283"
auto_power_level: "enable"
auto_power_low: "285"
auto_power_target: "<your_own_value>"
band: "802.11a"
band_5g_type: "5g-full"
bandwidth_admission_control: "enable"
bandwidth_capacity: "290"
beacon_interval: "291"
bss_color: "292"
call_admission_control: "enable"
call_capacity: "294"
channel:
-
chan: "<your_own_value>"
channel_bonding: "160MHz"
channel_utilization: "enable"
coexistence: "enable"
darrp: "enable"
drma: "disable"
drma_sensitivity: "low"
dtim: "303"
frag_threshold: "304"
frequency_handoff: "enable"
iperf_protocol: "udp"
iperf_server_port: "307"
max_clients: "308"
max_distance: "309"
mode: "disabled"
power_level: "311"
power_mode: "dBm"
power_value: "313"
powersave_optimize: "tim"
protection_mode: "rtscts"
rts_threshold: "316"
sam_bssid: "<your_own_value>"
sam_captive_portal: "enable"
sam_password: "<your_own_value>"
sam_report_intv: "320"
sam_security_type: "open"
sam_server: "<your_own_value>"
sam_ssid: "<your_own_value>"
sam_test: "ping"
sam_username: "<your_own_value>"
short_guard_interval: "enable"
spectrum_analysis: "enable"
transmit_optimize: "disable"
vap_all: "enable"
vaps:
-
name: "default_name_331 (source wireless-controller.vap-group.name system.interface.name)"
wids_profile: "<your_own_value> (source wireless-controller.wids-profile.name)"
zero_wait_dfs: "enable"
split_tunneling_acl:
-
dest_ip: "<your_own_value>"
id: "336"
split_tunneling_acl_local_ap_subnet: "enable"
split_tunneling_acl_path: "tunnel"
tun_mtu_downlink: "339"
tun_mtu_uplink: "340"
wan_port_mode: "wan-lan"
Return Values
Common return values are documented here, the following are the fields unique to this module:
| Key | Returned | Description |
|---|---|---|
| build
string
|
always |
Build number of the fortigate image
Sample:
1547
|
| http_method
string
|
always |
Last method used to provision the content into FortiGate
Sample:
PUT
|
| http_status
string
|
always |
Last result given by FortiGate on last operation applied
Sample:
200
|
| mkey
string
|
success |
Master key (id) used in the last call to FortiGate
Sample:
id
|
| name
string
|
always |
Name of the table used to fulfill the request
Sample:
urlfilter
|
| path
string
|
always |
Path of the table used to fulfill the request
Sample:
webfilter
|
| revision
string
|
always |
Internal revision number
Sample:
17.0.2.10658
|
| serial
string
|
always |
Serial number of the unit
Sample:
FGVMEVYYQT3AB5352
|
| status
string
|
always |
Indication of the operation's result
Sample:
success
|
| vdom
string
|
always |
Virtual domain used
Sample:
root
|
| version
string
|
always |
Version of the FortiGate
Sample:
v5.6.3
|
Authors
- Link Zheng (@chillancezen)
- Jie Xue (@JieX19)
- Hongbin Lu (@fgtdev-hblu)
- Frank Shen (@frankshen01)
- Miguel Angel Munoz (@mamunozgonzalez)
- Nicolas Thomas (@thomnico)
© 2012–2018 Michael DeHaan
© 2018–2021 Red Hat, Inc.
Licensed under the GNU General Public License version 3.
https://docs.ansible.com/ansible/latest/collections/fortinet/fortios/fortios_wireless_controller_wtp_profile_module.html