junipernetworks.junos.junos_interface – (deprecated, removed after 2022-06-01) Manage Interface on Juniper JUNOS network devices
Note
This plugin is part of the junipernetworks.junos collection (version 1.2.1).
To install it use: ansible-galaxy collection install junipernetworks.junos
.
To use it in a playbook, specify: junipernetworks.junos.junos_interface
.
New in version 1.0.0: of junipernetworks.junos
DEPRECATED
- Removed in
-
major release after 2022-06-01
- Why
-
Updated modules released with more functionality
- Alternative
-
Use junipernetworks.junos.junos_interfaces instead.
Synopsis
- This module provides declarative management of Interfaces on Juniper JUNOS network devices.
Note
This module has a corresponding action plugin.
Requirements
The below requirements are needed on the host that executes this module.
- ncclient (>=v0.5.2)
Parameters
Parameter | Choices/Defaults | Comments | ||
---|---|---|---|---|
active
boolean
|
|
Specifies whether or not the configuration is active or deactivated
|
||
aggregate
list /
elements=dictionary
|
List of Interfaces definitions.
|
|||
active
boolean
|
|
Specifies whether or not the configuration is active or deactivated
|
||
delay
integer
|
Time in seconds to wait before checking for the operational state on remote device. This wait is applicable for operational state argument which are
state with values
up /
down ,
tx_rate and
rx_rate.
|
|||
description
string
|
Description of Interface.
|
|||
duplex
string
|
|
Interface link status.
|
||
enabled
boolean
|
|
Configure interface link status.
|
||
mtu
integer
|
Maximum size of transmit packet.
|
|||
name
string /
required
|
Name of the Interface.
|
|||
neighbors
list /
elements=dictionary
|
Check the operational state of given interface
name for LLDP neighbor.
The following suboptions are available.
|
|||
host
string
|
LLDP neighbor host for given interface
name .
|
|||
port
string
|
LLDP neighbor port to which given interface
name is connected.
|
|||
rx_rate
string
|
Receiver rate in bits per second (bps).
This is state check parameter only.
Supports conditionals, see
Conditionals in Networking Modules
|
|||
speed
string
|
Interface link speed.
|
|||
state
string
|
|
State of the Interface configuration,
up indicates present and operationally up and
down indicates present and operationally
down
|
||
tx_rate
string
|
Transmit rate in bits per second (bps).
This is state check parameter only.
Supports conditionals, see
Conditionals in Networking Modules
|
|||
delay
integer
|
Default:
10
|
Time in seconds to wait before checking for the operational state on remote device. This wait is applicable for operational state argument which are
state with values
up /
down ,
tx_rate and
rx_rate.
|
||
description
string
|
Description of Interface.
|
|||
duplex
string
|
|
Interface link status.
|
||
enabled
boolean
|
|
Configure interface link status.
|
||
mtu
integer
|
Maximum size of transmit packet.
|
|||
name
string
|
Name of the Interface.
|
|||
neighbors
list /
elements=dictionary
|
Check the operational state of given interface
name for LLDP neighbor.
The following suboptions are available.
|
|||
host
string
|
LLDP neighbor host for given interface
name .
|
|||
port
string
|
LLDP neighbor port to which given interface
name is connected.
|
|||
provider
dictionary
|
Deprecated
Starting with Ansible 2.5 we recommend using
connection: network_cli or
connection: netconf .
For more information please see the
Junos OS Platform Options guide.
A dict object containing connection details.
|
|||
host
string
|
Specifies the DNS host name or address for connecting to the remote device over the specified transport. The value of host is used as the destination address for the transport.
|
|||
password
string
|
Specifies the password to use to authenticate the connection to the remote device. This value is used to authenticate the SSH session. If the value is not specified in the task, the value of environment variable
ANSIBLE_NET_PASSWORD will be used instead.
|
|||
port
integer
|
Specifies the port to use when building the connection to the remote device. The port value will default to the well known SSH port of 22 (for
transport=cli ) or port 830 (for
transport=netconf ) device.
|
|||
ssh_keyfile
path
|
Specifies the SSH key to use to authenticate the connection to the remote device. This value is the path to the key used to authenticate the SSH session. If the value is not specified in the task, the value of environment variable
ANSIBLE_NET_SSH_KEYFILE will be used instead.
|
|||
timeout
integer
|
Specifies the timeout in seconds for communicating with the network device for either connecting or sending commands. If the timeout is exceeded before the operation is completed, the module will error.
|
|||
transport
string
|
|
Configures the transport connection to use when connecting to the remote device.
|
||
username
string
|
Configures the username to use to authenticate the connection to the remote device. This value is used to authenticate the SSH session. If the value is not specified in the task, the value of environment variable
ANSIBLE_NET_USERNAME will be used instead.
|
|||
rx_rate
string
|
Receiver rate in bits per second (bps).
This is state check parameter only.
Supports conditionals, see
Conditionals in Networking Modules
|
|||
speed
string
|
Interface link speed.
|
|||
state
string
|
|
State of the Interface configuration,
up indicates present and operationally up and
down indicates present and operationally
down
|
||
tx_rate
string
|
Transmit rate in bits per second (bps).
This is state check parameter only.
Supports conditionals, see
Conditionals in Networking Modules
|
Notes
Note
- This module requires the netconf system service be enabled on the remote device being managed.
- Tested against vSRX JUNOS version 15.1X49-D15.4, vqfx-10000 JUNOS Version 15.1X53-D60.4.
- Recommended connection is
netconf
. See the Junos OS Platform Options. - This module also works with
local
connections for legacy playbooks. - For information on using CLI and netconf see the Junos OS Platform Options guide
- For more information on using Ansible to manage network devices see the Ansible Network Guide
- For more information on using Ansible to manage Juniper network devices see https://www.ansible.com/ansible-juniper.
Examples
- name: configure interface junipernetworks.junos.junos_interface: name: ge-0/0/1 description: test-interface - name: remove interface junipernetworks.junos.junos_interface: name: ge-0/0/1 state: absent - name: make interface down junipernetworks.junos.junos_interface: name: ge-0/0/1 enabled: false - name: make interface up junipernetworks.junos.junos_interface: name: ge-0/0/1 enabled: true - name: Deactivate interface config junipernetworks.junos.junos_interface: name: ge-0/0/1 state: present active: false - name: Activate interface config junipernetworks.junos.junos_interface: name: ge-0/0/1 state: present active: true - name: Configure interface speed, mtu, duplex junipernetworks.junos.junos_interface: name: ge-0/0/1 state: present speed: 1g mtu: 256 duplex: full - name: Create interface using aggregate junipernetworks.junos.junos_interface: aggregate: - name: ge-0/0/1 description: test-interface-1 - name: ge-0/0/2 description: test-interface-2 speed: 1g duplex: full mtu: 512 - name: Delete interface using aggregate junipernetworks.junos.junos_interface: aggregate: - name: ge-0/0/1 - name: ge-0/0/2 state: absent - name: Check intent arguments junipernetworks.junos.junos_interface: name: '{{ name }}' state: up tx_rate: ge(0) rx_rate: le(0) - name: Check neighbor intent junipernetworks.junos.junos_interface: name: xe-0/1/1 neighbors: - port: Ethernet1/0/1 host: netdev - name: Config + intent junipernetworks.junos.junos_interface: name: '{{ name }}' enabled: false state: down
Return Values
Common return values are documented here, the following are the fields unique to this module:
Key | Returned | Description |
---|---|---|
diff.prepared
string
|
when configuration is changed and diff option is enabled. |
Configuration difference before and after applying change.
Sample:
[edit interfaces] + ge-0/0/1 { + description test-interface; + }
|
Status
- This module will be removed in a major release after 2022-06-01. [deprecated]
- For more information see DEPRECATED.
Authors
- Ganesh Nalawade (@ganeshrn)
© 2012–2018 Michael DeHaan
© 2018–2019 Red Hat, Inc.
Licensed under the GNU General Public License version 3.
https://docs.ansible.com/ansible/2.10/collections/junipernetworks/junos/junos_interface_module.html